안녕하세요 기계주인장 입니다.

오늘은 전선절단기 판매 정보 입니다. 제품 구입에 작은 도움이라도 되었으면 좋겠습니다.

전선절단기는 기계주인장 블로그와 함께 하시기 바랍니다^^

 

 

 

 

 

 

- 동력(motive power) : 2 hp 단상 모터(Motor)
...(주문시 변경가능-The specification is adjustable by requirements.)

- 전압(Voltage) : 220 v (주문시 사양맞춤 가능-The specification is adjustable by requirements.)

- 소비전력(electric power) : 1.5 kw

- 유압펌프압력(Pressure of oil pressure pump) : 240BAR

- 순간압력(Instantaneous pressure) : 260BAR

- 용량(Capacity) : ALP 1 AB-3(2CC)

- 절단최대범위
...TH803 : 전선의 직경 Ø 90m/m 사진(좌) wire diameter 90mm (see the left picture).
...TH804 : 전선의 직경 Ø 90m/m 사진(우) wire diameter 95mm (see the right picture).

- 높이(Product Hight) : 350 mm

- 너비(Product Width) : 280 mm

- 길이(Product Length) : 420 mm

- 절단실린더 무게(칼날이 조립된상태) Weight of blade &; cylinder (as the blade is assembled)
.. TH803 : 실린더+칼날(Cylinder+ Blade)=6.8kg
...TH804 : 실린더+칼날(Cylinde+r Blade)=6.3kg

- 총중량(Product Weight) : 80 kg

- 유압기본체(BOX)와 절단실린더의 거리(Distance between box and cutting cylinder) :
...고압호스 약 10m high pressure hose about 10 m

 


 
  [ 제품의특징 ]

1. 전선의 크기, 모양, 종류가 다양한 폐 전선 절단작업을 힘들지 않고 유압의 원리를 을 적용케 하여
....실린더 손잡이 전방좌측에 설치된 전기 스위치를 작동시키면 (누름) 굵은 전선을 손쉽게 절단 할 수 있습니다.
....It can easily cut a variety of sizes, shapes, or types of wires by applying the oil pressure principle.
....It also can easily cut a thick wire by operating a electric switch installed at the front and left side of the
....cylinder handle.

2. 절단기의 본체에 바퀴 및 손잡이가 부착되어있어 이동하기가 쉽습니다.
....It is easy to move with its wheel and handle on the box.

3. 유압기 본체와 한 쌍의 칼날이 결합된 실린더의 거리가 10m 로 자유롭게 이동하면서 작업할 수 있습니다.
....It can freely operate with the 10 meter distance between the box and the cylinder where a pair of
....blades are assembled.

4. 엉켜있는 폐전선의 모양, 방향 그 형태에 따라 칼날이 결합된 실린더의 방향을 자유롭게 움직여 가면서
....절단 할 수 있습니다.
....The cylinder with an assembled blade can freely move to cut according to the shape an direction of
....the tangled wire.

TH-803의 특징 : 한쌍 칼날이 합쳐지는 지점 한쪽 칼날의 끝부분에 칼날의 벌어짐을 방지하는 칼날 안내구가
.......................설치되어 있어 칼날의 수명을 연장시켜 줍니다.
.......................The blade guiding hole is installed at the end of joint part of a pair of blades, which
.......................prevents the blades from getting wider and lengthens the span of blades.

[ 사용방법 ]

1. 한쌍의 절단 칼날이 결합 설치된 실린더의 손잡이 전방 좌측에 있는 누름 스위치를 작동(누름) 시키면
....실린더 내의 피스톤 로드가 전진 및 후진 TH-803 (전진) TH-804 (후진)과 동시에 절단 칼날이 오므려
....지면서 전선이 자동 절단됩니다.
....Press the button at the front and left side of the cylinder handle where a pair of cutting blades are
....jointly installed. Then the piston rod in the cyliner moves back and forth and at the same time the
....cutting blades close up to automatically cut the wire.

2. 절단이 끝난 후에는 스위치에서 손가락을 떼어 주시면 종래의 위치(초기상태)로 복귀합니다.
....After finighing cutting process, release the button and then return it to the beginning position.

3. 칼날의 끝 부분(경사를 이루고 있는 곳)에는 크기가 작은 전선 일지라도 걸리지 않게 하고 절단 하고자 하는
....전선이 칼날 내구에서 벗어나지 않게 하여 절단 하십시오.
....Please note that even a small wire should not be caught at the end of blades (sloping part) and the
....wire should be kept within the blade endurance.

[ 주의사항 ]

1. 본 절단기는 전선 절단 전용이므로 동(구리) 전선 이외는 그 용도가 맞지 않음으로 경도가 강한 금속 종류는
....절단하지 마십시오.
....This cutter is for wire cutting only. Do not cut materials harder than copper.

2. 탈피한 후의 전선 즉 피복이 없는 전선에는 절단하지 마십시오.
....Do not cut the uncoated side of wire.

3. 누름 스위치를 작동시켜 절단이 끝난 후에는 빨리 스위치에서 손을 떼어 실린더 피스톤을 후진시켜 칼날이
....초기상태로 복귀 됨으로써 후진시 실린더와 칼날이 결합된 모든 부분을 무리가 가지 않도록 보호합시다.
....Pleae make sure to rlease the pressing button after cutting process so that the cylinder piston can
....return to the beginning postion and the joint parts of cyliner and blades can be protected.

4. 실린더 피스톤의 압력이 매우 높으므로 인체 부위의 절단 사고가 일어나지 않도록 사용방법설명서를 숙지
....한 후 관리 책임자의 허락을 받고 사용하십시오.
....The cyliner piston is in high pressure. So be fully aware of the instruction before operating and operate
....it under the supervision of a manager to protect the operators.


  
TH-803 TH-804 TH-806
 


 


[ 제품사양 ]
- 모터 : 단상 2HP (주문자 사양가능)
- 소비전압 : 105kw
- 유압펌프 압력 : 240BAR
- 절단최대범위 : 250
- 유압펌프 용량 : 4.5CC
- 너비 : 500㎜
- 길이 : 1320㎜
- 높이 : 880㎜
- 충중량 : 240kg

 

 
 
[ 제품특징 ]
1. 굵은 지중선이나 비철계통으로 피복된 특수전선, 기타 잡철을 절단하는데 사용합니다.
2. 굵은 지중선이나 특수전선을 절단할 때 절단부가 고정식이므로 작업시의 안전성이 보장됩니다.
3. 칼날은 착탈이 쉬운 구조로 되어 있어 누구나 쉽게 교환할 수 있도록 제작되었습니다.


 

[ 사용방법 ]
1. 전기를 입력(ON)하여 유압을 자동 시킨다.
2.누림보턴을 눌러 폐전선을 전달한다.
3. 절단시는 눌림보턴을 계속 눌러 폐전선을 절단한다.  
 
[ 주의사항 ] 
1. 본 절단기는 전선(구리) 절단 전용이므로 전선이외의 경도가 강한 금속 종류는 절단하지 마십시오.
2. 눌림보턴을 눌러 절단이 끝나면 즉시 눌림보턴의 눌림을 해제하여 칼날이 초기상태로 복귀시킨다.
3. 칼날등에 직접 손이 닿지 않도록 칼날이 조직에 주이ㅢ하고 사용설명서를 숙지한 후 관리자의 허락을
...득한 후 사용하십시오. 
 

 

 

 

 

 

 

 

 

 

 

 

 

 

 



 

 

 

 

 

제품번호 : 247456
기본사양 : 전선절단기
모델명
판매금액 : 가격협의


 제품분류일반산업기계/기타 > 전선가공/탈피/차핑기
상세분류
제품현황재고보유
제조사
거래가능지역전체
가격할부불가능
 제품상태신제품
AS여부가능
세금계산서가능

 

 

 

 

▶ 전선절단기 신품 가격 및 제품 상세정보 바로가기

 

 

Posted by 구콰차
,